How to Hook Up a Water Line to a Refrigerator From the Sink | Home Guides | SF Gate

How to Hook Up a Water Line to a Refrigerator From the Sink

refrigerator hook up ice maker

To straighten coiled tubing not the entire roll , have a partner hold the end of the tube flat on the floor, then push the roll against the floor while unrolling to the length you need to go through the cabinets. Read more on Kitchen. She writes mainly home improvement, health and travel articles for various online publications. Hand-tighten the fitting, then tighten three-quarters of a turn using a small wrench on both sides of the fitting. If you are lucky, there will be a hookup in your kitchen wall near the refrigerator.

Required Tools for this Project

Attach the valve to the pipe using two pipe clamps. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Slip the compression nut that came with the kit over the newly installed supply line. Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench. Add pipe compound to the threads to make it easier to tighten compression joints. Make sure the threads are facing the end of the line.

Shut off water at the new valve. Connect the ferrule and pressure nut to the hose at the refrigerator end. Attach the nut to the refrigerator valve.

If applicable to your refrigerator, run the tubing through the hose clamp to hold it at the preferred angle. Plug in the refrigerator. Set the ice maker to the "on" position as indicated in your specific model. Discard the first two or three batches of ice to flush the system. Thomas Ferraioli began writing in His work has been featured in national publications like "Parents" and "U.

Skip to main content. Tighten nuts if leaks occur. Be sure to cut the end of the tubing square. Then slide on the compression fittings, lubricate the threads on the refrigerator fitting with pipe compound and screw on the tubing.

Hand-tighten the fitting, then tighten three-quarters of a turn using a small wrench on both sides of the fitting. Avoid last-minute shopping trips by having all your materials ready ahead of time. Read more on Kitchen. This article will show you how to run a water line to your refrigerator for an automatic ice maker and water dispenser. The story and how-to photos cover tapping into an existing water pipe the toughest part of the job and attaching copper tubing to the fridge.

If you're replacing your old refrigerator, this DIY project covers everything you need to know to install the plumbing.

Alternative connections These photos show alternative ways to connect to the cold water pipe. Reader's Digest Taste of Home Recipes. Sign Up for our newsletters! Insert the new water line into the opening on the tee. Slide the compression nut over the male threads and tighten it on the adapter. Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter.

Place the end of the water line you intend to connect to the refrigerator into a 5-gallon bucket. Turn the cold water supply valve on beneath the sink. Let 1 or 2 gallons of water run through the new line to remove the air. Turn off the supply line. Slip the remaining compression nut and ferrule over the refrigerator end of the new water line. Connect the line to the water line connector on the back of the refrigerator.

Turn the supply line on once again. Watch for leaks at all the connections. Tighten the connections slightly if you see a leak. If tightening the connection does not stop the leak, turn off the water, remove the connector and add additional thread-seal tape before reconnecting the water line. Plug your refrigerator into the wall.

Iamges: refrigerator hook up ice maker

refrigerator hook up ice maker

Watch for leaks at all the connections.

refrigerator hook up ice maker

Slip the remaining compression nut and ferrule over the refrigerator end of the new water line.

refrigerator hook up ice maker

Twist the male end of a quick-tee adapter onto the valve. Set the ice maker to the "on" position as indicated in your specific model. Turn the cold water supply valve on beneath the sink. Eharmony dating pharmacist Up for our newsletters! Skip to main content. Connect the tubing to the valve by hand, then turn refgigerator extra time with a wrench. But do clamp the tubing to the fridge.